Active
Disk Image

FAQ

How to erase hard drive? Windows7 logo   How to erase hard drive? Intel logo

How to load Active@ Boot Disk over the network via PXE environment on a Windows 10 computer?

There are several steps required to do this: configuring the WinPE WIM, Boot Manager and PXE Server.

For the configuration steps, let's assume that inserted Active@ Boot Disk has a F: letter in our configuration environment.

Step 1: Copy WinPE Source Files onto the PXE Server

Step 2: Configure boot configuration

These are a few of the files that were copied over to the server in Step 1

For more details, see “Creating a BCD file for PXE boot”

Step 3: Deployment process

Boot the client machine through PXE, connected to the network. After pressing initializing the PXE boot, the system should handle the rest. Here’s what will happen:

For more detailed instructions, read the Microsoft TechNet official documentation Configuring a PXE Server:

Configuring a TFTP server is made simple with a tool called Serva. Download it here

This too is an “Automated PXE Server Solution Accelerator” that supports a variety of server protocols. The ones we will be configuring are TFTP and DHCP.

Configure your TFTP settings

Once the settings are configured, reset the application and your PXE server should be fully operational!

Creating a BCD file for PXE boot:

This entire process is done in Windows Command Prompt. Be sure to run it as administrator.

1. Create a BCD store using bcdedit.exe:

bcdedit /createstore c:\BCD

2. Configure RAMDISK settings:

bcdedit /store c:\BCD /create {ramdiskoptions} /d "Ramdisk options"
bcdedit /store c:\BCD /set {ramdiskoptions} ramdisksdidevice boot
bcdedit /store c:\BCD /set {ramdiskoptions} ramdisksdipath \boot\boot.sdi
bcdedit /store c:\BCD /create /d "winpe boot image" /application osloader

The last command will return a GUID, for example:

The entry { bb254249-93e9-11e7-84cb-6c71d9da760e } was successfully created.

Copy this GUID for use in the next set of commands. In each command shown, replace "GUID1" with your GUID.

3. Create a new boot application entry for the Windows PE image:

bcdedit /store c:\BCD /set {bb254249-93e9-11e7-84cb-6c71d9da760e} device ramdisk=[boot]\Boot\boot.wim,{ramdiskoptions} 
bcdedit /store c:\BCD /set {bb254249-93e9-11e7-84cb-6c71d9da760e} path \windows\system32\winload.exe 
bcdedit /store c:\BCD /set {bb254249-93e9-11e7-84cb-6c71d9da760e} osdevice ramdisk=[boot]\Boot\boot.wim,{ramdiskoptions} 
bcdedit /store c:\BCD /set {bb254249-93e9-11e7-84cb-6c71d9da760e} systemroot \windows
bcdedit /store c:\BCD /set {bb254249-93e9-11e7-84cb-6c71d9da760e} detecthal Yes
bcdedit /store c:\BCD /set {bb254249-93e9-11e7-84cb-6c71d9da760e} winpe Yes

4. Configure BOOTMGR settings (remember to replace GUID1 in the third command with your GUID):

bcdedit /store c:\BCD /create {bootmgr} /d "boot manager"
bcdedit /store c:\BCD /set {bootmgr} timeout 30 
bcdedit /store c:\BCD -displayorder {bb254249-93e9-11e7-84cb-6c71d9da760e} -addlast

5. Copy the BCD file to your TFTP server:

copy c:\BCD \\PXE-1\TFTP\Boot\BCD

Your PXE/TFTP server is now configured. You can view the BCD settings that have been configured using the command bcdedit /store &lgt; BCD file location> /enum all. See the following example. Note: Your GUID will be different than the one shown below.

C:\>bcdedit /store C:\BCD /enum all
Windows Boot Manager
--------------------
identifier              {bootmgr}
description             boot manager
displayorder            {bb254249-93e9-11e7-84cb-6c71d9da760e}
timeout                 30

Windows Boot Loader
-------------------
identifier              {bb254249-93e9-11e7-84cb-6c71d9da760e}
device                  ramdisk=[boot]\boot\boot.wim,{ramdiskoptions}
description             winpe boot image
osdevice                ramdisk=[boot]\boot\boot.wim,{ramdiskoptions}
systemroot              \Windows
detecthal               Yes
winpe                   Yes

Setup Ramdisk Options
---------------------
identifier              {ramdiskoptions}
description             ramdisk options
ramdisksdidevice        boot
ramdisksdipath          \boot\boot.sdi

 
Configure your TFTP settings

Data Recovery

Data Utility

Data Security

Data Backup

CD/DVD Tools

欧美色视频日本片免费,欧美色色,成 人 色综合